pet

Friday Favorites 015

Pillows & Textiles – Freedom Tree  |  Banana Leaf Foldover Clutch – Chapman at Sea  |  Hand-dyed Indigo Scarf – Garner Blue  |  Bandhani Indigo Cushion Cover – Napeansea  |  Dog Waste Bag Holder – Boots & Arrow  |  MCM Hanging Plant Holder – Sonadora in Love  |  California Embroidered Hoop – Foxes & Rabbits

Happy National Bow Tie Day!

Today, August 28, is National Bow Tie Day. So c’mon, America, let’s celebrate with cute pictures of animals wearing bow ties!

And if all of this cuteness a little too much for your taste, here’s a touch of creepy to send you on your way.

Happy Bow Tie Day!

Cats, Cats, Cats

Have you every taken a photograph and thought to yourself, “Man, I really like the light and balance in this picture, I just wish it had more cats.”? You’re not alone.  Cat Effects is a free app that lets you draw or stamp a variety of different cats onto your iPhone/iPad photos. Or just make your own feline font:

Cat Alphabet by Martin Löfqvist, an illustrator based in Sweden

DIY Dog Ramp

DIY DOG RAMP

     

My 80 pound Rhodesian mix recently had reconstructive ACL surgery on both of her back legs, rendering her pretty useless for 6 months or so. She hates being picked up and I hate carrying her, so daily stair hauls was out of the question. As I was researching dog ramps online, I soon discovered that the only inexpensive options were either ugly or shoddy. So I drew up my own plans, used salvaged wood, and built my own ramp for less than $40. Good luck and happy building!

MATERIALS

  • Two 12″ x [Length] x 3/4″ planks
  • One 120″ beam, cut into 5 equal pieces–24″ long each
  • Six strips of wood casing–24″ long each
  • Indoor-outdoor carpeting, 24″ x [Length]
  • Twelve wood screws, 3/8 or 1/2″ long
  • Ten wood screws–2.5″ long
  • Waterproofing primer/paint
TOOLS NEEDED

  • Outdoor carpet glue
  • Power screwdriver
  • Power saw
  • Tape measure
  • Paint brush

ESTIMATED TIME: 1.5 hours

STEP 1

Measure the length from the top of the stairs to where you want the ramp to end and add 4″. The ramp I built is 76″ long, but feel free to adjust this to suit your needs. Be sure that the ramp will have a gentle incline, so your pet doesn’t have to struggle when using it.

STEP 2

Cut beam into 5 equal pieces. These will be used to connect the two pieces of plywood, as well as minimize ramp sagging.

     

STEP 3

Line up the cut beams in equal intervals. I used 11″ intervals, but you should adjust this to your personal ramp length.

Place one plank on the left half of the beams.

Screw into place with 2.5″ wood screws.

Repeat with right side.

STEP 4

Place wood casing in equal intervals along the top of the ramp. I used 8.5″ intervals.

Attach the casing with 1/2″ wood screws.

The wood casing will act as “speed bumps” for your pet, allowing him/her to maintain traction on the ramp.

STEP 5

Paint entire ramp with a mildew-resistent primer to weatherproof your ramp for outside use. I ended up using 3 coats, but you could get by with less.

Optional: After priming, you could paint your ramp a fun color to match your house.

STEP 6

Cut outdoor carpet to fit your casing intervals.

Spread glue onto the bottom of the carpet pieces and place them along the top of the ramp.

Be sure to allow proper dry time & follow all instructions that come with the glue.

It may take a few days for your pet to get used to the new ramp. Start off by guiding your him/her along the ramp while leashed, using treats or toys as an incentive. Good luck and happy building!